Specifications
Specifications subject to change without notice.
Maximum Distance* 1000 feet
Maximum Input 1.1 Vp-p
Bandwidth (video) DC to 6 MHz
Bandwidth (audio) 20 Hz to 20 kHz
Impedance (video) 75 ohms
Impedance (audio) 600 ohms minumum
Insertion Loss Less than 2 dB per pair over the frequency range
Return Loss Greater than 15 dB over the frequency range
Common Mode Rejection Greater than 40 dB over the frequency range
Unshielded Twisted Pair Maximum capacitance: 20 pf/foot
Cabling Specifications Impedance: 100 ohms @ 1 MHz
(24 gauge or lower solid Attenuation: 6.6 dB/1000 ft. @ 1 MHz
copper) Cat 5, Cat 5e, Cat 6, Cat 7 compatible
Connectors One (1) S-Video 4-pin and two (2) RCA to one (1) RJ45
RJ45 Pinout S-Video Luma: 7 & 8, pair 4
S-Video Chroma: 4 & 5, pair 1
Audio 1: 1 & 2, pair 2
Audio 2: 3 & 6, pair 3
Temperature Operating: 32 to 131 F (0 to 55 C)
Storage: -4 to 185 F (-20 to 85 C)
Humidity: up to 95%
Enclosure Black plastic
Dimensions 4.3” x 2.5” x 1”
Weight 0.2 lbs (3.2 oz.)
Ordering Information AVO-SVA2-F: single AVO-SVA2-F balun in bulk packaging
AVO-SVA2-PAC-F: two AVO-SVA2-F baluns in retail-ready
packaging
Warranty 2 years
* Distances and picture quality may be affected by cable grade, cable quality, source and
destination equipment, RF and electrical interference, and cable patches. Intelix specifications are
based on straight-through cabling with standard-grade Cat 5.
Contact Information
Intelix
2222 Pleasant View Road
Middleton, WI 53562
Toll-free: 866-4-MATMIX
Phone: 608-831-0880
Fax: 608-831-1833
www.intelix.com
Intelix AVO-SVA2-F S-Video and Audio Balun
Installation ManualInstallation Manual
Installation ManualInstallation Manual
Installation Manual
The AVO-SVA2-F balun allows the transmis-
sion of a single S-Video signal and two analog
audio signals over unshielded twisted pair
(UTP) cable, such as Cat 5. Used in pairs,
AVO-SVA2-F baluns eliminate costly and
bulky S-Video cable, allowing the connection
of S-Video equipment to any convenient
modular outlet.
The AVO-SVA2-F balun allows pre-existing
twisted pair cable to be used in such
applications as classroom video distribution,
overhead projector systems, PC-training systems, and tradeshow PC-demo systems in the
S-Video environment.
To install an AVO-SVA2-F balun, perform the following steps:
1. Turn off power and disconnect the S-Video source and S-Video monitor.
2. Make certain the modular outlets and cross connects to which you will connect the
AVO-SVA2-Fs are configured properly and labeled appropriately to identify the
circuit.
3. Verify the desired twisted pairs are not used with other LAN or telephone equipment.
4. Connect the balun to the S-Video port of the source equipment (i.e., DVD or VCR).
Connect the audio connectors to the audio source.
5. Connect a 4-pair Cat 5 cable from the RJ45 8-position modular jack of the AVO-
SVA2-F to a structured cable, such as Cat 5.
6. Connect the second balun’s RCA inputs to the destination equipment.
7. Connect the 4-pair Cat 5 cable from the RJ45 8-position modular jack of another
AVO-SVA2-F to the structured cable attached to the first balun.
8. Power on the S-Video equipment at both ends and adjust the monitor image and audio
levels to the desired settings.
Installation
Caution: Do not attempt to open the balun housing. There are no user-serviceable parts
inside the AVO-SVA2-F. Opening the unit will void your warranty.
Caution: Do not mount the balun over equipment ventilation openings. Covering the
openings may cause the equipment to overheat.
AvoCat
Series
Caution: Do not connect the AVO-SVA2-F to a telecommunication outlet
wired to unrelated equipment. Making such a connection may damage
the equipment and/or balun. Please ensure all wiring is “straight-
through.”
(2 stránky)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce